• DATES:
• ADDRESSES:
• Examining the AD Docket
• FOR FURTHER INFORMATION CONTACT:
• SUPPLEMENTARY INFORMATION:
• Comments Invited
• Discussion
• Relevant Service Information
• FAA’s Determination
• Proposed AD Requirements
• Differences Between This Proposed AD and the Service Information
• Costs of Compliance
• Authority for This Rulemaking
• Regulatory Findings
• List of Subjects in 14 CFR Part 39
• The Proposed Amendment
• PART 39—AIRWORTHINESS DIRECTIVES
• (a) Comments Due Date
• (b) Affected ADs
• (c) Applicability
• (d) Unsafe Condition
• (e) Compliance
• (f) Alternative Methods of Compliance (AMOCs)
• (g) Related Information

We must receive comments on this proposed AD by November 10, 2014.

You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
• Fax: 202-493-2251.
• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.
• Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Lycoming Engines, 652 Oliver Street, Williamsport, PA 17701; phone: 800-258-3279; fax: 570-327-7101; Internet: www.lycoming.com/Lycoming/SUPPORT/TechnicalPublications/ServiceBulletins.aspx. You may view this service information at the FAA, Engine & Propeller Directorate, 12 New England Executive Park, Burlington, MA. For information on the availability of this material at the FAA, call 781-238-7125.

You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2014-0540; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

Norm Perenson, Aerospace Engineer, New York Aircraft Certification Office, FAA, Engine & Propeller Directorate, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 516-228-7337; fax: 516-794-5531; email: norman.perenson@faa.gov.

We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2014-0540; Directorate Identifier 2014-NE-10-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

We issued Special Airworthiness Information Bulletin (SAIB) NE-08-32 on July 3, 2008. The SAIB recommended actions to correct the condition of a propeller governor shaft set screw coming loose. This proposed AD was prompted by additional events of propeller governor shaft set screws coming loose due to improper installation, which could result in the shaft penetrating the plug at the front of the crankcase and causing a loss of engine oil and a loss of engine power. In some reported events, engine oil was deposited on the windshield, restricting pilot visibility. The loose set screw could also enter the rotating system and cause damage to the camshaft and valve lifters. Safety is further diminished if failure occurs during aerobatic maneuvers, especially at low altitudes, due to reduction in pilot reaction time. These conditions, if not corrected, could result in damage to the engine, and damage to the airplane. This proposed AD would require application of Loctite 290, or equivalent, to the threads of the propeller governor shaft set screw at each installation of the set screw in addition to the peening of crankcase hole threads. We are proposing this AD to prevent the propeller governor shaft set screw from coming loose, causing damage to the engine, and damage to the airplane.

We reviewed Lycoming Engines Service Instruction (SI) No. 1343B, dated June 15, 2007. The SI describes procedures for securing the propeller governor shaft set screw.

We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of these same type designs.

This proposed AD would require application of Loctite 290, or equivalent, to the threads of the propeller governor shaft set screw at each installation of the set screw in addition to the peening of crankcase hole threads.

Lycoming Engines SI No. 1343B, dated June 15, 2007, specifies the use of Loctite 290, in addition to peening of the crankcase hole threads, to secure the set screw in place. This AD allows the use of Loctite 290, or equivalent thread-locking, anaerobic, single-component sealing compound that meets military specification Mil-S-46163A, Type III, Grade R. The SI also requires these actions at next overhaul, whereas this AD requires these actions at any installation of the propeller governor shaft set screw.

We estimate that this proposed AD would affect about 2,330 engines installed on airplanes of U.S. registry. We also estimate that it will take about 0.1 hours per engine to comply with this AD. The average labor rate is $85 per hour. Prorated parts life will cost about $1 per engine. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $22,135.

Title 49 of the United States Code specifies the FAA’s authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska to the extent that it justifies making a regulatory distinction, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

[FR Doc. 2014-21675 Filed 9-10-14; 8:45 am]

BILLING CODE 4910-13-P